Soundweave
Guide · Anyone new to audio routing

What is a virtual audio cable, and when do you need one?

A virtual audio cable is an audio device that exists only in software. One app plays sound into it and another app records from it, like a cable between a speaker output and a microphone input. It is how Discord, a game and your music become separate sources in OBS, and how a call app gets a mix of your own.

Windows 10 & 11, macOS 14+5 min readUpdated

What you need

  • Nothing, to read this page. To try a cable: Windows 10 (22H2) or Windows 11, 64-bit, or macOS 14 or later on Apple Silicon, and Soundweave.
  • Virtual Cable Support, a one-time setup explained at the end of this page.

What a virtual audio cable is

Real audio gear has outputs you plug a cable into, and inputs where the other end goes. A virtual audio cable does the same inside the computer. Windows lists each Soundweave cable twice, as a speaker and as a microphone; macOS shows it as one device with both. Whatever an app plays into the speaker side comes out of the microphone side, where another app can record it.

IllustrationIllustration: sound goes in at one side of a cable and comes out of the other
  • App Aplays sound
  • Virtual cablein as speaker, out as microphone
  • App Brecords it

The system sees an ordinary audio device, so any app that lets you choose a speaker or a microphone can use a cable. No plug-in is needed.

What people use virtual cables for

  • Streaming. Discord, the game and your music arrive in OBS as separate sources, each with its own volume. The OBS guide builds this step by step.
  • Calls and meetings. A call app gets a microphone that carries your cleaned-up voice, or your voice plus music. The microphone guide shows how.
  • Podcasts and interviews. You record yourself and a remote guest on separate tracks, and the guest does not hear their own voice back. The podcast guide covers it.

Why you usually need two cables per app

A cable is a loop: what goes in comes out, and that is all it does. To mix an app on the way, Soundweave sits in the middle. The app plays into one cable, the “in” cable. Soundweave brings that cable in as a strip, mixes it, and plays the result into a second cable, the “out” cable, that the other app records from. That is two cables for each app you want on its own.

IllustrationIllustration: the signal path of one app through two cables
  • Appplays sound
  • Cable “in”app plays into it
  • Soundweavestrip, fader, bus
  • Cable “out”bus plays into it
  • OBS or call apprecords it

Never use one cable both ways. If a strip reads a cable and a bus also plays into that same cable, the sound goes round in a circle and you hear it doubled. Every cable is either a way in or a way out, never both.

When you do not need a cable

You do not need a virtual cable to change the volume of one app, or to send an app to other speakers: on Windows 11, Settings › System › Sound › Volume mixer does both. A microphone or any other hardware input comes into Soundweave directly, without a cable.

A cable earns its place when one app has to hear another app, separately from everything else on the PC.

Add your first cable in Soundweave

  1. Open Devices in the title bar. If the status card says Ready, go on. Otherwise choose Install Virtual Cable Support. It asks for approval once: a Windows administrator approval, or your password on macOS.
  2. Choose Add Cable and give the cable a name that says what it is for, for example Game in.
  3. In the app you want to use it with, choose the cable as its speaker or its microphone. Windows shows the name you chose followed by (Soundweave 1), (Soundweave 2) and so on. If an app does not list the cable straight away, close it and start it again.
The Soundweave Virtual devices page: Virtual Cable Support ready and three active cables named Game in, Chat out and Stream out, each with two input and two output channels at 48 kilohertz and the place where it is used in the mixer
The Devices page in an example session. Each cable shows what it is used for in the mixer.

Four cables are included. The Steam add-ons give 6, 8, 15 or 30, and you can rename a cable at any time. The virtual cables page has the details.

Good to know

You choose the buffer size in Settings: smaller buffers mean less delay and a higher risk of crackles. Soundweave supports up to 30 cables.

Troubleshooting

An app does not list the cable
Start the app again after you added the cable. Some apps only look for audio devices when they start.
I hear nothing from an app
An app that plays into an “in” cable is silent until its strip is sent to an output you listen to, for example a bus with your headphones. The OBS guide shows the routing.
The sound echoes or doubles
A cable is probably used both ways. Give the way in and the way out a cable of their own.
Windows lists the cable twice
That is intended: one speaker and one microphone, both with the name you chose.

Questions

Is a virtual audio cable the same as a virtual audio device?

In practice, yes: an audio device made of software that shows up next to your real speakers and microphones. “Cable” stresses that sound goes in at one side and comes out of the other.

How many cables do I need?

Two for every app you want on its own: an “in” cable the app plays into and an “out” cable the other app records from. The OBS guide builds a full example.

How many cables does Soundweave include?

Four. The Steam add-ons give 6, 8, 15 or 30, and you can rename a cable at any time.

Do virtual audio cables work on macOS?

Yes. Soundweave adds virtual cables on macOS 14 or later with Apple Silicon. The one-time approval asks for your password instead of a Windows administrator approval.

Does a virtual cable add delay?

You choose the buffer size in Settings: smaller buffers mean less delay and a higher risk of crackles.

Keep going

Set it up on your PC.

Soundweave is out on Steam for Windows 10 and 11 and macOS 14 or later. The first four virtual cables are included. $9.99 on Steam, with a free 7-day demo on the same page.