What you need
- Windows 10 (22H2) or Windows 11, 64-bit, and Soundweave.
- A saved settings file (.xml) from your current virtual mixer. Such a program usually keeps its latest settings in a folder in your Documents, and Soundweave looks there for you. You can also pick a file you saved under your own name.
- Your audio devices connected, so Soundweave can match them by name.
What the import does
The import reads the settings file, matches the devices in it to the devices on your PC, and builds a preview. It brings over the inputs, the buses and the routes between them, the level of each, and the EQ, gate and compressor settings that Soundweave has a counterpart for. Nothing in the mixer changes while you look at the preview.
Two things stay as they are: your original file, which is only read and never changed, and your current mixer, until you press Add to current setup or Replace current setup….
Open the import page
In Soundweave open Settings › Import. Choose Detect saved settings and Soundweave looks in the usual places. The files it finds are listed with their date and size, newest first. Choose Preview next to the one you want.
Did you save the file somewhere else, or under your own name? Choose Choose file… and pick the .xml file.
Read the preview
The preview starts with a summary: how many inputs and buses will be created, how many routes there are, and how many items cannot be created. Notes below it explain what was left out, for example an output that had no device in the file.
Then come one table for the inputs and one for the buses. Every row shows the device Soundweave matched, the level, where the input is sent, and the result:
- Will be created. The device was found. Notes under it name the values that Soundweave limited to its own ranges, for example an EQ band that was narrower than it allows.
- Will be created (choose a source afterwards). The old input was one of the program’s own virtual inputs, which has no device behind it. The strip is made without a source, and you give it one afterwards.
- Not created. The reason is in the row, for example that its device was not found. Connect the device and load the file again, or add that input in the mixer yourself.

Add it, or replace your setup
At the bottom of the preview you choose how to apply it:
- Add to current setup adds the inputs and buses to the mixer. It is possible while the mixer has no inputs.
- Replace current setup… removes the current inputs and buses first and then creates the ones from the file. Soundweave asks you to confirm.
If a step fails, Soundweave puts your current setup back and tells you whether that worked. When the import is done, Open the mixer takes you to the result.
Want to be able to go back? Save your current setup as a profile before you replace it: open Settings › Profiles and save. You can switch back from the title bar.
Check it and point your apps at Soundweave
Open the mixer and play something. The meters on the strips should move.
Strips that were created without a source need one before they make sound. Choose a source for each, for example a virtual cable that its app plays into. The OBS guide shows how to add cables and bring an app in on its own strip.
Your apps still use the devices of the old program. In each app’s audio settings, or in Windows sound settings, choose the Soundweave cable instead. Change one app at a time and check that it works before you move on to the next. When everything works, remove the virtual cables and drivers you no longer use: a short list of audio devices is easier to read.
Troubleshooting
- Detect saved settings finds nothing
- Soundweave only looks in the usual places. Choose “Choose file…” and pick the .xml file you saved.
- An input says “Not created”
- Read the reason in the Result column, for example that its device was not found. Connect the device, choose “Choose another file”, load the same file again and check the preview.
- “Add to current setup” is greyed out
- Adding is possible while the mixer has no inputs, and the reason is shown under the buttons. Use “Replace current setup…” instead, or remove the inputs from the mixer first.
- A bus has no output
- Its output device was not found in the file or on your PC. After the import, open the bus and choose its output.
- The import stopped part way
- Soundweave puts your previous setup back and reports whether that worked. If it says the setup is only partly back, check the mixer before you go on.
- It sounds different from before
- Soundweave has its own EQ, gate and compressor, and values outside its ranges are limited (the notes in the preview say which). Use the numbers as a starting point and adjust by ear. The microphone guide covers the effects.
Questions
Does the import change my old settings file?
No. Soundweave only reads it, and the file stays exactly as it was.
Which settings files can Soundweave read?
Saved mixer settings files (.xml) from common Windows virtual audio mixers. If Soundweave cannot read your file, the import tells you so and nothing changes.
Is everything imported?
The preview is the complete list. It shows every input and bus in the file, what will be created and what cannot be, and which values were limited. What it does not list is not imported.
Can I undo an import?
If a step fails, Soundweave puts your previous setup back by itself. To be able to go back after a finished import, save your current setup as a profile before you replace it.
Do I need the other program installed?
No. Soundweave only needs the settings file.
Keep going
Set it up on your PC.
Soundweave is out on Steam for Windows 10 and 11 and macOS 14 or later. The first four virtual cables are included. $9.99 on Steam, with a free 7-day demo on the same page.